CARTER P76300M

Product Details Attribute

Carter Fuel Pump & Housing Assemblies decrease cost and labor time by ensuring a seamless repair from start to finish! Every Carter assembly includes features that bring exclusive benefits to each application. These may include:

OE Matched Electrical Connections - Make installation simple
Metal Clamps - Prevent blowoffs on the fuel supply hose
Silver Alloy Buttons - Increase the life of the sender assembly
over-Molded Armature - Reduces fuel flow turbulence
Carbon Commutator - Eliminates oxidation and high electrical erosion
Rubber Feet - Reduce noise and vibration during operation
Float Arm - Pre-mounted and calibrated to ensure proper fuel read
CleanScreen™ Technology - Internal and external filtration provides 40% more dirt-holding capacity (graphic below)

Benefits of Purchasing a Fuel Pump & Housing Assembly

Purchasing just the fuel pump is less expensive up-front, but a complete Fuel Pump & Housing Assembly provides added benefits:

Extend Service Life: New strainer(s), hoses, sensors and other components help resolve problems that could be caused by more than just the pump.
Reduce Install Time: Since you don't have to disassemble the housing, which could lead to damage, replacement becomes a simple swap, dramatically reducing installation time.
Save Money: The cost of the assembly is often cheaper than buying the components individually, and means you only have to do the job once.

Prevent Premature Fuel Pump Failure

Preventing premature fuel pump failure is far less expensive and time consuming than continuing to replace the pump. There are three common causes for premature fuel pump failure:

ELECTRICAL ISSUES

Poor electrical connections will mimic symptoms of a failed pump, sometimes resulting in unnecessary replacement. Before replacing the pump:

Use a Fuel System Tester to test pump pressure is within expected range
Use an Electrical Tester to test for bad wiring, burnt or corroded connectors
Check / Replace faulty Fuse(s) and Relay

BEFORE REPLACEMENT

FUEL CONTAMINATION

Dirt, rust or debris in the fuel can clog strainers and stick to internal pump components. When replacing the pump:

Replace Fuel Filter or Fuel Strainer
Empty and clean the tank with Fuel Tank Cleaner
Fill tank with fresh, uncontaminated fuel of appropriate grade

DURING REPLACEMENT

PUMP DAMAGE / OVERHEATING

Running low on gas causes your fuel to heat up quicker, and your pump to work harder. After replacing the pump:

Maintain at least 1/4 tank of fuel and use a Fuel Additive / Conditioner to keep pump cool and lubricated
If vehicle is stored without use, drain tank to prevent pump corrosion from fuel oxidation

AFTER REPLACEMENT

Additional Resources

Fuel System Diagnostic Check-List

Attention California Customers - No Proposition 65 warning is required with this product.

Alternate/OEM Part Number(s)

OEM / Interchange Numbers: 16141184276, 16146752499, 16146752895, 16146766942, SP5008M

Warranty Information

CARTER Warranty Information:12 months: Carter Mechanical Fuel Pumps, Carter Fuel System Accessories. Limited Lifetime: Carter Electric Fuel Pumps and Assemblies.Warranty Details

CAPA CERTIFIED or NSF CERTIFIED

CAPA Certified or NSF Certified parts bear the seal of independent, third party organizations guaranteeing fitment and quality equal to original equipment. These parts may be required if your insurance company is paying for the repair.

Specifications
Mounting Hardware Included	No
Height (MM)	242
Housing Material	POM
Gasket or Seal Included	Yes
Connector Gender	Male
Connector Shape	Rectangle
Terminal Quantity	4
Terminal Type	Pin
Connector Color	White
Terminal Gender	Male
Voltage	12
Regulator Included	No
Wiring Harness Length (MM)	242.0
Inlet Type	Strainer
Outlet Type	Quick Connect
Internal Or External Strainer	Internal
Lock Ring Included	No
Outlet Quantity	1
Pump Type	Electric
Strainer Included	Yes
Wire Harness Included	No
Outlet Outside Diameter (MM)	9.4
Fuel Filter Included	No
Minimum Flow Rating	39
Top Mount Diameter (MM)	127.0
Negative Ground	Yes
Fuel Sending Unit Included	Yes
Minimum Pressure (PS)	54.0
Resistance Ohms Empty	70.0
Resistance Ohms Full	395.0
Fuel Tank Pressure Sensor Included	No
Inlet Fitting Thread Size (in)	3/8